Filter Modules - 1st up RIVER Synths Marble [Video] Tilt, Mids, STEREO

Want to talk about music hardware or software that doesn't include Reason?
User avatar
O1B
Posts: 2037
Joined: 26 Jan 2015

10 Dec 2020

Mutable Instruments. Blades - so Ordered.
Image

Dual multimode filter
A DUAL MULTIMODE FILTER…

A CV-controlled overdrive circuit capable of wavefolding.
A clean 12dB/octave multimode filter self-oscillating cleanly across the audio range.
Times two.
... And this could have stopped here...



https://mutable-instruments.net/modules/blades/

User avatar
O1B
Posts: 2037
Joined: 26 Jan 2015

11 Jan 2021

Cwejman MMF-2 Stereo Filter

- true stereo mode, or as
- two independent filters

The module is build around three functional blocks; filter, saturation stage and :thumbs_up: mix.

w/ Noise...


:thumbs_up: FILTER: The heart of the MMF-2 are two four pole multi mode filters with six selectable outputs for the main stereo outputs; low pass, low-band pass, band pass, band-high pass, high pass and notch + bypass.

Three outputs/filter are available too; low pass, band pass and high pass and which are not affected by the saturation in the post mode.

:thumbs_up: SATURATION: The saturation stage consist of a saturation stage with dominant even harmonics (HARD) and with dominant odd harmonics (SOFT).

Mix? Dry/WET

Image

User avatar
O1B
Posts: 2037
Joined: 26 Jan 2015

12 Feb 2021

Joranalogue Filter 8: https://joranalogue.com/collections/eur ... s/filter-8

Im positive Selig talked about this but, cant find the thread.
I ordered the last two from Control. On Faith.


GENERATE 3 FEATURES

VCO with through-zero modulation
Through-zero frequency, phase, and amplitude modulation
Fundamental, even, and odd outputs with bipolar control of level
Full output mixed from harmonic outputs
Precise 1 v/oct tracking over entire range
Can be used as an LFO with a range of frequency from six minutes per cycle to 27kHz
Hard and soft sync
1 v/oct trim potentiometer for fine tracking adjustment

Killer architecture:
MS-20 OTA - MY FAV!!! :puf_smile: :puf_smile:
LPs, 6dB HP, Band, Notch, Saturation, Octature
Image

User avatar
O1B
Posts: 2037
Joined: 26 Jan 2015

07 Mar 2021

Blades....
O1B-BladesnnBeads-001.jpg
O1B-BladesnnBeads-001.jpg (920.21 KiB) Viewed 483 times
Nice Filter - w/Morphing capabilities.
So far, it DOES make the material BETTER than without - :thumbs_up:
I now have to pit it against some OTAs. (I haven't checked what kind of filter Blades is.. :redface: )

DRIVE works :thumbs_up: ! - But, it's easy to overdo - go easy.
It is not the BE ALL of DRIVES - but, it holds it's own. :thumbup:
I like that you can knob/add in increments vs. some with 'switches'

I've only used it in Serial mode (I think), and have not RTFM, yet.

There seems to be a bit of a Dead Zone in the lows - but, I have only tested it with Full Mixes vs drums/synths.

I like it. Im keeping it. It sounds Good, and it a Great Swiss Army for
- Parallel vs Serial vs DUAL INDEPENDENT (Filtering into FX modules)
- All around Routing
- Drive. Those two Drive Knobs DO make a Difference.
- Morphing - not many out there - much less Good Ones. :puf_smile:
- Ample CV

It's a Keeper!

(Beads - the 'Reverberance' is nice!)

Post Reply
  • Information
  • Who is online

    Users browsing this forum: No registered users and 8 guests