Complex from Propellerhead

[BRIGGS]

The default patch Canada is clicking now, so to me it's a bug.

It's too obvious now. It's highly likely, it will get fixed.

[Loque]

The default patch Canada is clicking now, so to me it's a bug.

It's too obvious now. It's highly likely, it will get fixed.

Anybody made a bug report?

[BRIGGS]

It's too obvious now. It's highly likely, it will get fixed.

Anybody made a bug report?

ok, done

[Noiserunner]

Is it just at my computer or is it impossible to add automation to the "Master" knob of Complex-1?
(Afaik) Every other RE can be automated this way.
I stumbled across it today when i made a drone sound with Complex-1 and tried to change the volume over time. So I have to automate the channel volume .

[BRIGGS]

Is it just at my computer or is it impossible to add automation to the "Master" knob of Complex-1?
(Afaik) Every other RE can be automated this way.
I stumbled across it today when i made a drone sound with Complex-1 and tried to change the volume over time. So I have to automate the channel volume .

It's not showing up in the combinator list, either.

[Loque]

The clicking is now fixed.

[BRIGGS]

The clicking is now fixed.

woo hoo!!!

[tobypearce]

Is it just at my computer or is it impossible to add automation to the "Master" knob of Complex-1?
(Afaik) Every other RE can be automated this way.
I stumbled across it today when i made a drone sound with Complex-1 and tried to change the volume over time. So I have to automate the channel volume .

I normally add a Selig Gain device and use that for simple volume automation.
I used to automate the SSL volume level but this makes it difficult to tweak the volume later in the mixing process.

[Noiserunner]

I normally add a Selig Gain device and use that for simple volume automation.

Thank you for the hint.
It is probably such an obvious solution, that I didn't think of it myself .
I don't own the Selig Gain, but there are ReGain Audio Gain Assistant or kHs Gain, which are free. Today evening I will give them a try.

[selig]

Is it just at my computer or is it impossible to add automation to the "Master" knob of Complex-1?
(Afaik) Every other RE can be automated this way.
I stumbled across it today when i made a drone sound with Complex-1 and tried to change the volume over time. So I have to automate the channel volume .

I normally add a Selig Gain device and use that for simple volume automation.
I used to automate the SSL volume level but this makes it difficult to tweak the volume later in the mixing process.

Instrument volume and channel volume (fader) are at the extreme opposite ends of the signal path, and therefore do different things. Putting Selig Gain after the device would be identical to automating the volume (or using CV to control volume/panning/etc). This would however not be the best way to add fader automation - you would instead put Selig Gain in the post-everything channel insert to do this (and it would have to be the last device in the insert to ensure correct functioning). Apologies if I'm stating the obvious here…

[ab459]

Folks, there is question about Filter self-oscillating in Complex1 - why it works (self-oscilate at maximum resonance) only from HP filter output ? (And from LP - no).
This is intended behavior ?
In user manual i did not found any mention about this difference. Just phraze "At maximum amount (of Res) the filter will self-resonate."

[SebAudio]

Is it just at my computer or is it impossible to add automation to the "Master" knob of Complex-1?
(Afaik) Every other RE can be automated this way.
I stumbled across it today when i made a drone sound with Complex-1 and tried to change the volume over time. So I have to automate the channel volume .

It's not showing up in the combinator list, either.

The noise rate knob can't be automated. Can you confirm ? I'll make a ticket if so, thank you